退火温度对新型锆合金薄板带材析出相和织构的影响

采用扫描电镜和超高分辨透射电镜,对具有良好冲制性能的新型锆合金薄板成品带材进行含晶粒、第二相粒子等在内的显微组织研究,并探索真空退火处理条件下温度对带材显微组织的影响。结果显示:新型锆合金薄板成品带材晶粒平均尺寸2.17 μm,存在{0001}<1010>和{0001}<1120>两种织构,大部分晶粒<1120>平行带材RD方向,较少晶粒<1010>平行带材RD方向;第二相粒子分布在晶粒内部及晶界,平均尺寸114 nm,尺寸较大的为不规则椭圆形的Zr-Nb-Fe相,尺寸较小的为圆形的β-Nb相;热处理退火温度降低,带材晶粒尺寸减小,第二相粒子细小弥散分布;新型锆合金薄板成品带材良好冲制性能主要源于轧制积累应变诱发再结晶过程进行充分,导致晶粒细小及孪晶发生破碎;相对轧制变形,退火对带材冲制性能影响不显著。     

不同镀层结构钢的耐盐雾腐蚀性能比较

通过盐雾试验模拟潮湿环境,对裸钢试片、电镀锌钢试片、化学镀镍-磷钢试片和化学镀镍-钴-磷钢试片进行了宏观形貌、微观形貌和腐蚀产物成分分析,比较了四个试片的耐盐雾腐蚀性能。结果表明:在盐雾环境中,四个试片均会发生电化学腐蚀,生成不同的腐蚀产物;在盐雾腐蚀周期内,裸钢试片的腐蚀速率最高,化学镀镍-磷钢试片和化学镀镍-钴-磷钢试片的腐蚀速率较低;四个试片在腐蚀过程中的阳极反应和阴极反应不同,腐蚀后的微观形貌存在明显差异。     

生物滴滤床法降解二氯甲烷废气的因素影响特征

二氯甲烷作为溶剂广泛应用于制药行业，其挥发性废气对人类健康和大气环境的危害极大。本文采用生物滴滤床对某制药厂浓度范围在0.02~2g/m³的二氯甲烷废气进行了为期132天的中试规模实验。在适宜的停留时间、温度、喷淋量和pH等实验条件下，控制适当的进气浓度可得到高效去除效率并且废气出口浓度达标。实验揭示了生物膜内生物降解是过程的限制因素，结果表明，在喷淋量为1200L/h、进气浓度范围为0.45~0.65g/m³时该生物系统去除效率最高可达98.9%，最大去除负荷可达EC_max=155.25g/(m³·h)。随着进气浓度的增加，去除负荷随之增大，而去除效率下降，废气出口浓度超标，表明生物滴滤系统已处于反应控制。此外，间歇实验表明，该生物系统具有良好的稳定性。指出生物滴滤床的设计、运行取决于当地的二氯甲烷废气排放标准。     

Hand hygiene and surface cleaning should be paired for prevention of fomite transmission

Touching contaminated surfaces might lead to the spread of pathogens, that is, the fomite transmission route. Although hand- and surface-hygiene practices are potentially important non-pharmaceutical interventions for the fomite route, the two interventions have been mostly studied separately in the literature. In this study, we develop a new conceptual model based on the law of mass action, analyze the temporal diffusion of contaminated surfaces and hands, and verify the model with simulations in an assumed norovirus outbreak in a buffet restaurant. A quantitative hygiene criterion is developed for the required frequency of surface disinfection and hand hygiene to control the fomite transmission in indoor environments. To eliminate surface contaminations, the product of pathogen-removal rates (including hygiene and natural death) on hands and surfaces must be no smaller than that of the human hand and surface contact frequency (ie, the net removal product must be non-negative). When the net removal product is negative, the number of contaminated surfaces and hands would show a logistic growth trend and finally approach the equilibrium. Our approach sheds light into how to optimize the combined use of hand hygiene and environmental decontamination for the best effectiveness under different settings.     

铁矿排土场不同基质改良方法下生态修复效果评价

开展4种铁矿排土场基质改良方法的现场修复实验；进行修复后的土壤理化性质、肥力性质、重金属污染特征，以及植被生长指标检测；确定了排土场生态修复效果的评价因子；利用灰色理论关联度分析法确定权重；根据各评价因子的指数进行统计学加权计算，最终得出生态修复效果评价指数。结果表明：40%粒径-5 mm排土场原矿土+60%黄土+刺槐的组合对排土场生态修复具有较好的效果，优于其它修复组合。建立的生态修复效果评价方法，较全面考虑了多种土壤和植被指标因素，对现场生态修复工程具有良好的借鉴和参考价值。     

X80管线钢在力电化学耦合作用下CO2腐蚀行为的研究

以典型的管线钢材料X80钢为对象,采用动电位极化和电化学阻抗谱技术,研究了在弹性拉伸应力(60%σ_(ys))和塑性拉伸应力(108%σ_(ys))状态下,不同CO_2分压和Cl~-质量分数对材料腐蚀的影响规律。结果表明:受拉伸应力作用的X80钢腐蚀速率随CO_2分压的增大而增大,但并非单纯正相关关系;随Cl~-质量分数的增大,呈现先升高后降低的规律,当Cl~-质量分数为3.5%时,X80钢的腐蚀速率达到最大值。此外,塑性应力状态下X80钢的腐蚀速率明显高于弹性应力状态下的值,原因是塑性应力提高了金属表面的电化学反应活性。     

以酸解TEOS为硅源合成可控孔径和粒径NaP分子筛

利用盐酸预处理TEOS得到的硅凝胶为硅源,铝酸钠为铝源,通过水热合成法制备了一种晶粒尺寸和孔径大小可控的NaP分子筛.利用不同时间酸解TEOS得到的硅凝胶合成NaP分子筛,但合成的样品杂晶较多且形貌不规整;采用正交试验,通过调节晶化时间、晶化温度、溶液pH值和水硅比,以达到样品提纯、形貌规整的目的.对样品进行SEM、XRD、N2物理吸附等表征,分析样品的形貌、结晶度和孔径分布等.并对样品进行铜离子吸附性能测试,得到NaP分子筛对Cu2+的有效去除率为98.9％.利用预先酸解TEOS得到的硅凝胶合成NaP分子筛的方法,为工业污水净化提供一定的理论依据及指导.     

PP/PCL/石墨/碳纳米管复合材料的制备及电性能分析

采用熔融共混法制备了石墨（G）、碳纳米管（CNTs）与聚丙烯（PP）、聚己内酯（PCL）导电复合材料，通过改变G的添加量制备了系列导电复合材料。主要测试了熔体流动速率、力学性能、导电性能、电热性能，并进行了电子显微镜观察结构、差示扫描量热法分析、热失重分析。结果表明，PCL与PP混合后，PP的拉伸强度提升了4.375 MPa，在加入G/CNTs之后，力学性能受影响较大下降了约73.5 %；G/CNTs的加入还能有效降低PP的电阻率，使其从绝缘体变为半导体材料电阻率为7.83×10⁶ Ω·m；PP与PCL共混后复合材料的热稳定性得到了显著提高，初始分解温度从368.88 ℃升高至398.95 ℃，在加入G/CNTs管后又进一步提高至408.78 ℃。     

Making reusable reaction-bonded silicon nitride crucibles for silicon casting from kerf-loss silicon waste

Silicon kerf loss during wafer slicing and the broken quartz crucibles after silicon casting are two major solid wastes from photovoltaic (PV) industry. Especially, the recycle of kerf-loss silicon has become an urgent issue because near 100 000 t of solid wastes are generated every year. One of the most meaningful recycle routes of the kerf-loss silicon is to make silicon nitride crucibles to replace the quartz crucibles. In this study, we demonstrated how this is feasible through acid leaching refining, slip casting, and nitridation. The reaction-bonded silicon nitride (RBSN) crucibles after oxidation were found pure enough for silicon ingot growth. More importantly, they could be reused after ingot growth. With the present examples, the potential of using the kerf-loss silicon for fine ceramics is prominent.     

A Dual Inhibitor of DYRK1A and GSK3β for β-Cell Proliferation: Aminopyrazine Derivative GNF4877

Loss of β-cell mass and function can lead to insufficient insulin levels and ultimately to hyperglycemia and diabetes mellitus. The mainstream treatment approach involves regulation of insulin levels; however, approaches intended to increase β-cell mass are less developed. Promoting β-cell proliferation with low-molecular-weight inhibitors of dual-specificity tyrosine-regulated kinase 1A (DYRK1A) offers the potential to treat diabetes with oral therapies by restoring β-cell mass, insulin content and glycemic control. GNF4877, a potent dual inhibitor of DYRK1A and glycogen synthase kinase 3β (GSK3β) was previously reported to induce primary human β-cell proliferation in vitro and in vivo. Herein, we describe the lead optimization that lead to the identification of GNF4877 from an aminopyrazine hit identified in a phenotypic high-throughput screening campaign measuring β-cell proliferation.